 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| HEP1601 THRU HEP1606 Features * Plastic package has Underwriters Laboratory Flammability Classification 94V-0 * Low forward voltage drop * High current capability * High reliability * Low power loss, high effciency * High surge current capability * High speed switching * Low leakage 3.7 0.2 CURRENT 16.0 Amperes VOLTAGE 50 to 600 Volts ITO-220A 10 0.5 3.2 6.4 0.1 4.5 0.2 2.7 2.7 0.2 Mechanical Data * Case : JEDEC ITO-220A molded plastic body * Terminals : Lead solderable per MIL-STD-750, method 2026 * Polarity : As marked * Mounting Position : Any * Weight : 0.08 ounce, 2.24 gram 5.08 + 0.7 0.2 13Min 1.3 0.2 15 0.3 0.5 2.4 PIN 1 CASE PIN 2 + Case Negative Suffix"R" PIN 1 CASE PIN 2 CasePositive + Dimensions in inches and (millimeters) Maximum Ratings And Electrical Characteristics (Ratings at 25E ambient temperature unless otherwise specified, Single phase, half wave 60Hz, resistive or inductive load. For capacitive load, derate by 20%) Symbols Maximum recurrent peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum average forward rectified current 0.375"(9.5mm) lead length @ at TA=100E Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC method) Maximum instantaneous forward voltage at 8.0A Maximum DC reverse current at rated DC blocking voltage TA=25E Maximum DC reverse current at rated DC blocking voltage TA=125E Maximum reverse recovery time (Note 1) Typical junction capacitance (Note 2) Typical thermal resistance (Note 3) Operating junction and storage temperature range IR VRRM VRMS VDC I(AV) IFSM VF HEP 1601 50 35 50 HEP 1602 100 70 100 HEP 1603 200 140 200 8.0 125 1.0 HEP 1604 300 210 300 HEP 1605 400 280 400 HEP 1606 600 420 600 Units Volts Volts Volts Amps Amps 1.3 10.0 1.7 Volts i A 100 Trr CJ 50 80 2.2 -55 to +150 -55 to +150 80 50 ns pF E /W E ReJC TJ TSTG Notes: (1) Test conditions: IF=0.5A, IR=1.0A, Irr=0.25A. (2) Measured at 1MHz and applied reverse voltage of 4.0 Volts. (3) Thermal resistance from junction to case mounting on heatsink. RATINGS AND CHARACTERISTIC CURVES HEP1601 THRU HEP1606 FIG . 1 -REVERSE RECOVERY TIME CHARACTERISTIC NONINDUCTIVE 50 NONINDUCTIVE 10 AND TEST CIRCUIT DIAGRAM trr +0.5A PULSE GENERATOR ( NOTE 2 ) 0 -0.25A DUT (+ ) 50Vdc (approx) (-) NONINDUCTIVE OSCILLOSCOPE (NOTE 2 ) -1.0A 1cm SET TIME BASE FOR 5/ 10ns / cm NOTES: 1 . RISE TIME = 7nsmax. INPUT IMPEDANCE= 1 MEGOHM 22pf 2 . RISE TIME = 10ns max. SOURSE IMPEDANCE = 50ohmsf AVERAGE FORWARD CURRENT . ( A ) FIG . 2 -MAXIMUM AVERAGE FORWARD CURRENT DERATING CURVE 20 16 12 8 4 0 0 50 100 150 A) 1000 FIG . 3 -TYPICAL REVERSE CHARACTERISTICS INSTANTAN EOUS REVERSE CURRET . ( Tj=125 C O 100 10 Tj=25 C O PE A K F O R W A R D S U R G E C U R R E N T . ( A ) CASE TEMPERATURE ( % ) . FIG . 4 -MAXIMUM NON - REPETITIVE FORWARD SURGE CURRENT 8.3ms Single Half Sine Tj=25oC Wave JEDEC Method 120 90 60 1 0.1 PERCENT OF RATED PEAK REVERSE VOLT AGE . (%) 20 40 60 80 100 120 140 CAPACITANCE ( pF) INSTANTANEOUS FORWARD CURRENT . ( A) 30 1 2 5 10 20 50 100 100 30 FIG . 6 -TYPICAL FRWARD CHARACTERISTICS 4 200 160 120 80 H E P 1 40 0 1 2 60 0.3 0.1 0.03 .01 0.4 0.6 0.8 1.0 HE HE P1 60 P1 240 Tj=25oC 1.0 60 1-1 60 5 Tj=25oC Pulse Width=300 1% Duty Cycle 6- 16 08 FIG . 5 -TYPICAL JUNCTIOON CAP ACITANCE PER LEG 3.0 HE P1 NMBER OF CYCLES AT 60Hz 60 HE 10 60 1-1 P1 60 5 s 6-1 60 8 5 10 20 50 100 REVERSE VOLTAGE . ( V) 200 500 1000 1.2 1.4 1.6 1.8 FORWARD VOLTAGE . ( V ) |
Price & Availability of HEP1601
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |